Berita perhiasan

Pandora Blue Stripes and Stones Ring Baolong: Pengaturan cakar teknik pengaturan perhiasan

Diposting di oleh Kingjy

Prong setting is a method of using metal claws to hold the gemstone. There are roughly two ways. One is to directly bend the metal claw in the direction of the gemstone and “grasp” the gemstone. This is a traditional prong setting mainly used for curved surfaces. , Square, trapezoid, random-shaped gems and jade inlays. The other is to carve a groove on the inner side of the prongs to squeeze the card inward. And to jam the gem, this is a modern prong setting method, mainly used for round diamond, oval and other faceted gems. The characteristic of the prong setting is to highlight the gem to the maximum.

Prong setting category

① According to the number of prongs, it can be divided into two prongs, three prongs, four prongs and six prongs.

② According to the shape of the prongs, it can be divided into triangular claws, round claws, square claws, angled claws, counter claws, pointed claws and conformal claws.

The process of prong setting faceted gems

1) Tools Flying saucer, needle-nose pliers, cutting pliers, triangle file, bamboo leaf file, tweezers, suction beads, motor, umbrella drill, peach drill.

2) Process steps of claw setting

Position: Place the gem on the setting position, pay attention to the size and thickness of the gem, and then use an appropriate umbrella drill or flying saucer to hold the position on the claw according to the size of the gem. The height of the holding position can be adjusted according to the thickness of the gem. set.

Car parking pit: If the gem is larger than the setting position, use umbrella diamond or peach diamond undercarriage to make the gem equal to the setting position. Then you need to perform corresponding operations according to the type of gemstones. Misalnya, use an umbrella to drill pits for cambered gemstones. When opening the pit, it should be consistent with the depth and height determined during the degree position, and the intersection point of the claw foot and the cylinder position cannot be empty.

Claw: Use tweezers to dip the gemstone into the ink, place the stone in the setting position diagonally and then push it upright with the tweezers. Ruo Shiping uses needle-nose pliers to clamp the symmetrical claws tightly to make the claws close to the gemstone, and then place the adjacent two Claw pliers are straight and tighten. Be careful not to shift or deviate the gemstones when the jaws are used, or cause the pliers marks to be too deep, otherwise it will affect the subsequent edge-holding process.

Shearing claw: Use shearing pliers to cut the claw. When cutting the claw, press the claw head by hand to avoid the claw head bounce off. When cutting the claw, pay close attention to the length of the claw, neither too long nor too short.

File claw: After cutting the claw, use a triangular file to file the claw to the height of the suction claw, and the claw height should be the same. Setelah itu, each time the inside of the claw is trimmed to the gemstone with a bamboo leaf file, and then the outside of the claw is rounded to facilitate the suction of the claw and the beads. When filing the claws, use the left thumb or appetite to specify the position, and be careful not to file the gem surface.

Suction claw: Use a suitable bead suction claw, swing evenly from the outside to the inside to both sides, until the claw head is sucked round and close to the gemstone, and the outside of the claw is sucked to the same height as the inside.

 

Desain Produsen Perhiasan OEM/ODM Kustom Perhiasan Anda Sendiri

Mari kita mulai : mo@kingjy.com

 

Guangzhou Jingying Fokus pada Kalung Cincin Grosir Kustom Gelang Anting Sterling Silver 925 perhiasan,Sterling Silver Gold berlapis 18K,14K,24K emas kuning,emas putih dan emas mawar.,merek logo atau kata -kata lain dengan ukiran laser sesuai dengan persyaratan pelanggan.

Kapasitas produksi bulanan kami terserah 50,000 Potongan Gelang Kalung Anting -anting Cincin Perhiasan.,Toko rantai perhiasan,toko outlet,Pedagang perhiasan,Perusahaan Merek Pedagang dan Perhiasan,profesional menyediakan membuat perhiasan khusus dan produksi massal berkualitas tinggi 925 Layanan perhiasan perak sterling.